The white wire is connected with the one terminal of the bulb, and the black wire is connected with the second terminal. Two wires coming from each switch are connecting to the light. Here the two switches are in the same box. Source: You don’t have to understand this figure much as the elaboration is mentioned above. In the light, both white and black wires are connected with the terminal. The neutral white that is the white wire is coming from the source and is connected with the white wire and is going to the light. We can see the two brass terminals both the black hot wires are connected with the two terminals of the switch. #Basement light switch teenagent plusSource: This is the wiring of the single pole switch, in this case, the power source is with the switch, plus two wires are coming from the switch to the light. Insert the configuration inside the box, tight the screw, and again turn ON the light to check.įollowing are some practical illustrations of the light switch wiring to make our minds and concepts more precise about what we have seen above. Now, connect the loop of the black wire to the terminal at the bottom of the switch.Ĭonnect the white wire in a hook shape at the top of the switch’s terminal. You have to work with the white, black, and one bare wire coming from the box you configured above.Ĭonnect the loop of the bare wire in a hook shape to both box and the switch. Now you have to configure the switch in such a way that power comes from the light. Now, insert the whole system into the plastic box, tight the screws, and power ON to test the light. Now, you have loose bare copper wire, create a loop from it same as above, make a hook shape of the loop, hook it with the green screw, and rotate the screw again clockwise. You have to make a loop for the copper wires inside the black wires by revolving them with the needle-nose pliers.Ĭonnect the black wire loop by making the hook shape to the terminal screw and twist the screw clockwise.ĭo the above step with other black wires too. Also, peel black and white wire for about ¾ inch.Ĭonnect the two copper wires with an extra copper wire. Strip off the wire’s sheath approximately 6 inches, and then you will see the black, green, and white wire. For this configuration, you will have to work with the three wires mentioned above. In the first step, the power comes to the switch and then travels to the light. We will go through the two primary configurations for wiring a light switch. Typically, we purchase a switch from the market but for some unique situations, when you have to make it by your hand, then follow these steps.įor wiring a switch, you must have these tools and equipment. #Basement light switch teenagent how toIn this section, we will talk about how to wire a light switch. When we make the switch close, it’s then contacted with the hot wire delivering the power to the load and then from the standard wire to the power source. What happens is there is always a space between the hot wire and the switch. But when you push the button to OFF the light, it entirely breaks the circuit, and the passing of electricity is interrupted. When the current is passed through the switch to the load, that is, bulbs, ceiling lights, etc. The green wire, a ground wire, connects with the green screw in the switch or the electrical box. The black or sometimes red wire, also known as the hot wire, goes into the brass screw. The white is also known as the neutral wire, and this wire connects with the silver screw. The colors of the wires in a light switch One is on the position where the black aka hot wire connects the circuit, and the other is on the side where the power source black wire connects it. The switch contains two brass terminals screws. Inside a light switch, there is a spring that makes the button move up and down. The switch’s outside is usually made up of plastic. But the light switch was invented for home lights to turn then ON or OFF and they are wall-mounted switches. You may see light switches in many devices like vehicles, home appliances, machines, etc. But as time flows, more advanced features have come with the switch like the dimmer switches that dim the light and ON/OFF it too, a time-dependent switch that works at a specified time, remotely controlled switch that you can control from a remote place. Usually, the switches only do ON or OFF the device that is connected with it. Switches are of different types and are used for different purposes. The light switch is an electrical component used to control and operate the lights, bulbs, the equipment connected with it, and any electrical outlet connected with it.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |